Skip to main content

PIC Serial Communication Tutorial (UART)

First, a quick history of RS232. What is RS232? It's just a name for a standard that has propagated from generation to generation of computers. The first computers had serial ports that used RS232, and even current computers have serial ports (or at least USB ports that act like RS232 ports). Back in the day, serial information needed to be passed from devices like printers, joysticks, scanners, etc to the computer. The simplest way to do this was to pass a series of 1s and 0s to the computer. Both the computer and the device agreed on a speed of information - 'bits per second'. A computer would pass image data to a printer at 9600 bits per second and the printer would listen for this stream of 1s and 0s expecting a new bit every 1/9600 = 104us (104 micro-seconds, 0.000104 seconds). As long as the computer output bits at the pre-determined speed, the printer could listen.
Zoom forward to today. Electronics have changed a bit. Before they were relatively high power, high voltage devices. The standard that is 'RS232' dictates that a bit ranges from -12V to +12V. Modern electronics do not operate at such high positive and negative voltages. In fact, our PIC  runs 0V to 5V. So how do we get our 5V micro to talk the RS232 +/-12V voltages? This problem has been solved by the IC manufacturers of the world. They have made an IC that is generically known as the MAX232 (very close to RS232, no?).
The MAX232 is an IC originally designed by a company called Maxim IC that converts the +/-12V signals of RS232 down to the 0/5V signals that our PIC  can understand. It also boosts the voltage of our PIC  to the needed +/-12V of the RS232 protocol so that a computer can understand our PIC  and vice versa. To get our PIC  IC sending serial characters to a computer, we have to send these serial signals through a MAX232 circuit so that the computer receives +/-12V RS232 signals. Don't worry if you're working with a chip labeled 'ICL232' or 'ST232' - these are just generics of the MAX232. Everyone says 'MAX232'. The ICs all function the same and nearly all have the same pinout.

                                                                 Discussion Group



Circuit


UART Library

The UART hardware module is available with a number of PIC compliant MCUs. The mikroC PRO for PIC UART Library provides comfortable work with the Asynchronous (full duplex) mode.
You can easily communicate with other devices via RS-232 protocol (for example with PC, see the figure at the end of the topic – RS-232 HW connection). You need a PIC MCU with hardware integrated UART, for example 16F887. Then, simply use the functions listed below.
  Important :
  • UART library routines require you to specify the module you want to use. To select the desired UART module, simply change the letter x in the routine prototype for a number from 1 to 2.
  • Switching between the UART modules in the UART library is done by the UART_Set_Active function (UART modules have to be previously initialized).
  • Number of UART modules per MCU differs from chip to chip. Please, read the appropriate datasheet before utilizing this library.
Library Routines
Generic Routines
UARTx_Init
Prototype
void UARTx_Init(const unsigned long baud_rate);
Returns
Nothing.
Description
Initializes desired hardware UART module with the desired baud rate. Refer to the device data sheet for baud rates allowed for specific Fosc. If you specify the unsupported baud rate, compiler will report an error.
Requires
You need PIC MCU with hardware UART.
UARTx_Init needs to be called before using other functions from UART Library.
Parameters :
  • baud_rate: requested baud rate
Refer to the device data sheet for baud rates allowed for specific Fosc.
  Note : Calculation of the UART baud rate value is carried out by the compiler, as it would produce a relatively large code if performed on the library level.
Therefore, compiler needs to know the value of the parameter in the compile time. That is why this parameter needs to be a constant, and not a variable.
Example
// Initialize hardware UART1 and establish communication at 9600 bps
UART1_Init(9600);
UARTx_Data_Ready
Prototype
char UARTx_Data_Ready();
Returns
  • 1 if data is ready for reading
  • 0 if there is no data in the receive register
Description
Use the function to test if data in receive buffer is ready for reading.
Requires
UART HW module must be initialized and communication established before using this function. See UARTx_Init.
Example
// If data is ready, read it:
if (UART1_Data_Ready() == 1) {
 receive = UART1_Read();
 }
UARTx_Tx_Idle
Prototype
char UARTx_Tx_Idle();
Returns
  • 1 if the data has been transmitted
  • 0 otherwise
Description
Use the function to test if the transmit shift register is empty or not.
Requires
UART HW module must be initialized and communication established before using this function. See UARTx_Init.
Example
// If the previous data has been shifted out, send next data:
if (UART1_Tx_Idle() == 1) {
  UART1_Write(_data);
 }
UARTx_Read
Prototype
char UARTx_Read();
Returns
Returns the received byte.
Description
Function receives a byte via UART. Use the function UARTx_Data_Ready to test if data is ready first.
Requires
UART HW module must be initialized and communication established before using this function. See UARTx_Init.
Example
// If data is ready, read it:
if (UART1_Data_Ready() == 1) {
 receive = UART1_Read();
 }
UARTx_Read_Text
Prototype
void UARTx_Read_Text(char *Output, char *Delimiter, char Attempts);
Returns
Nothing.
Description
Reads characters received via UART until the delimiter sequence is detected. The read sequence is stored in the parameter output; delimiter sequence is stored in the parameter delimiter.
This is a blocking call: the delimiter sequence is expected, otherwise the procedure exits (if the delimiter is not found).
Parameters :
  • Output: received text
  • Delimiter: sequence of characters that identifies the end of a received string
  • Attempts: defines number of received characters in which Delimiter sequence is expected. If Attempts is set to 255, this routine will continuously try to detect the Delimiter sequence.
Requires
UART HW module must be initialized and communication established before using this function. See UARTx_Init.
Example
Read text until the sequence “OK” is received, and send back what’s been received:
UART1_Init(4800);                         // initialize UART1 module
Delay_ms(100);

while (1) {
  if (UART1_Data_Ready() == 1) {          // if data is received
    UART1_Read_Text(output, "OK", 10);    // reads text until 'OK' is found
    UART1_Write_Text(output);             // sends back text
 }
}
UARTx_Write
Prototype
void UARTx_Write(char data_);
Returns
Nothing.
Description
The function transmits a byte via the UART module.
Parameters :
  • _data: data to be sent
Requires
UART HW module must be initialized and communication established before using this function. See UARTx_Init.
Example
unsigned char _data = 0x1E;
...
UART1_Write(_data);
UARTx_Write_Text
Prototype
void UARTx_Write_Text(char * UART_text);
Returns
Nothing.
Description
Sends text via UART. Text should be zero terminated.
Parameters :
  • UART_text: text to be sent
Requires
UART HW module must be initialized and communication established before using this function. See UARTx_Init.
Example
Read text until the sequence “OK” is received, and send back what’s been received:
UART1_Init(4800);                         // initialize UART1 module
Delay_ms(100);

while (1) {
  if (UART1_Data_Ready() == 1) {          // if data is received
    UART1_Read_Text(output, "OK", 10);    // reads text until 'OK' is found
    UART1_Write_Text(output);             // sends back text
 }
}
UART_Set_Active
Prototype
void UART_Set_Active(char (*read_ptr)(), void (*write_ptr)(unsigned char data_), char (*ready_ptr)(), char (*tx_idle_ptr)())
Returns
Nothing.
Description
Sets active UART module which will be used by the UART library routines.
Parameters :
Requires
Routine is available only for MCUs with two UART modules.
Used UART module must be initialized before using this routine. See UARTx_Init routine
Example
UART1_Init(9600);                    // initialize UART1 module
UART2_Init(9600);                    // initialize UART2 module

RS485Master_Init();                  // initialize MCU as Master

UART_Set_Active(&UART1_Read, &UART1_Write, &UART1_Data_Ready, &UART1_Tx_Idle); // set UART1 active
RS485Master_Send(dat,1,160);        // send message through UART1

UART_Set_Active(&UART2_Read, &UART2_Write, &UART2_Data_Ready, &UART2_Tx_Idle); // set UART2 active
RS485Master_Send(dat,1,160);        // send through UART2
UART_Data_Ready
Prototype
char UART_Data_Ready();
Returns
  • 1 if data is ready for reading
  • 0 if there is no data in the receive register
Description
Use the function to test if data in receive buffer is ready for reading.
This is a generic routine which uses the active UART module previously activated by the UART_Set_Active routine.
Requires
UART HW module must be initialized and communication established before using this function. See UARTx_Init.
Example
// If data is ready, read it:
if (UART_Data_Ready() == 1) {
 receive = UART_Read();
 }
UART_Tx_Idle
Prototype
char UART_Tx_Idle();
Returns
  • 1 if the data has been transmitted
  • 0 otherwise
Description
Use the function to test if the transmit shift register is empty or not.
This is a generic routine which uses the active UART module previously activated by the UART_Set_Active routine.
Requires
UART HW module must be initialized and communication established before using this function. See UARTx_Init.
Example
// If the previous data has been shifted out, send next data:
if (UART_Tx_Idle() == 1) {
  UART_Write(_data);
 }
UART_Read
Prototype
char UART_Read();
Returns
Returns the received byte.
Description
Function receives a byte via UART. Use the function UART_Data_Ready to test if data is ready first.
This is a generic routine which uses the active UART module previously activated by the UART_Set_Active routine.
Requires
UART HW module must be initialized and communication established before using this function. See UARTx_Init.
Example
// If data is ready, read it:
if (UART_Data_Ready() == 1) {
 receive = UART_Read();
 }
UART_Read_Text
Prototype
void UART_Read_Text(char *Output, char *Delimiter, char Attempts);
Returns
Nothing.
Description
Reads characters received via UART until the delimiter sequence is detected. The read sequence is stored in the parameter output; delimiter sequence is stored in the parameter delimiter.
This is a blocking call: the delimiter sequence is expected, otherwise the procedure exits (if the delimiter is not found).
This is a generic routine which uses the active UART module previously activated by the UART_Set_Active routine.
Parameters :
  • Output: received text
  • Delimiter: sequence of characters that identifies the end of a received string
  • Attempts: defines number of received characters in which Delimiter sequence is expected. If Attempts is set to 255, this routine will continuously try to detect the Delimiter sequence.
Requires
UART HW module must be initialized and communication established before using this function. See UARTx_Init.
Example
Read text until the sequence “OK” is received, and send back what’s been received:
UART1_Init(4800);                         // initialize UART1 module
Delay_ms(100);

while (1) {
  if (UART_Data_Ready() == 1) {          // if data is received
    UART_Read_Text(output, "OK", 10);    // reads text until 'OK' is found
    UART_Write_Text(output);             // sends back text
 }
}
UART_Write
Prototype
void UART_Write(char data_);
Returns
Nothing.
Description
The function transmits a byte via the UART module.
This is a generic routine which uses the active UART module previously activated by the UART_Set_Active routine.
Parameters :
  • _data: data to be sent
Requires
UART HW module must be initialized and communication established before using this function. See UARTx_Init.
Example
unsigned char _data = 0x1E;
...
UART_Write(_data);
UART_Write_Text
Prototype
void UART_Write_Text(char * UART_text);
Returns
Nothing.
Description
Sends text via UART. Text should be zero terminated.
This is a generic routine which uses the active UART module previously activated by the UART_Set_Active routine.
Parameters :
  • UART_text: text to be sent
Requires
UART HW module must be initialized and communication established before using this function. See UARTx_Init.
Example
Read text until the sequence “OK” is received, and send back what’s been received:
UART1_Init(4800);                         // initialize UART1 module
Delay_ms(100);

while (1) {
  if (UART_Data_Ready() == 1) {          // if data is received
    UART_Read_Text(output, "OK", 10);    // reads text until 'OK' is found
    UART_Write_Text(output);             // sends back text
 }
}

This program demonstrates a simple data exchange via UART. When PIC MCU receives data, it immediately sends it back. If PIC is connected to the PC (see the figure below), you can test the example from the mikroC PRO for PIC terminal for RS-232 communication, menu choice Tools › Terminal.

Serial Terminal- Download


 

Code

 
char uart_rd;

void main() {
  ANSEL  = 0;                     // Configure AN pins as digital
  ANSELH = 0;
 
  UART1_Init(9600);               // Initialize UART module at 9600 bps
  Delay_ms(100);                  // Wait for UART module to stabilize
 
  UART1_Write_Text("Start");
  UART1_Write(10);
  UART1_Write(13);
 
  while (1) {                     // Endless loop
    if (UART1_Data_Ready()) {     // If data is received,
      uart_rd = UART1_Read();     // read the received data,
      UART1_Write(uart_rd);       // and send data via UART
    }
  }
}


Serial Terminal- Download



Check Our New Blog: Embedded Projects-Tutorials-Arduino-Android-Raspberry PI- Gadgets News - Embedded Hackes - New Embedded Products Intro etc 

 (click the Image Below to Visit the Blog)

www.google.co.in/url?sa=t&rct=j&q=&esrc=s&source=web&cd=1&cad=rja&ved=0CCoQFjAA&url=http%3A%2F%2Farrogancegizmo.blogspot.com%2F&ei=SMaRUsGzCYj_rAfA-4GoDw&usg=AFQjCNEw6Pm6VepdEnZlm1evPy5f0N2NdA&sig2=sG5PkXDQilaUfIan6u2Wzw&bvm=bv.56988011,d.bmk



See Also

 




Comments

  1. Serial communication has been using the RS232 for the UART examples/tutorials. However, computers at this present age no longer use/include RS232 ports. USB is used instead and it can be used for serial communication thru the COM port. What are the changes on the examples above to effectively do serial communication with PIC and your pc?

    ReplyDelete
  2. For USB to 232 converters no need of any modification

    ReplyDelete
  3. What if I am using transceiver, is the code is still the same?

    ReplyDelete
    Replies
    1. What type of transceiver you mean? If you mean RF transceiver you can use same code at a low baud rate.

      Delete
  4. I have been testing this procedures with Easy PIC v7 board and mikroBasic. So far, the loop is running endlessly and nothing is being detected as received. However, if I try to send from PIC to PC, it does work. I have ran with ICD and efectively, the Ready = 1, is never shown. My pc is TXing some numbers every 1000ms.

    Any idea what am I missing?

    ReplyDelete
  5. If the Ready!=1 please make sure that your PC is successfully sending something and it is received, there is a chance of hardware error MAX232 part. First test the code with simulated circuit in proteus or any other simulator.

    ReplyDelete
  6. For all those who need a make a terminal program to transmit and receive serial data...... here is a simple program to help you achieve that.... enjoy..

    http://www.goldeneye-enterprises.com/#!Serial-Communication---RS232---PC-to-Microcontroller/cz16/1

    ReplyDelete
  7. can this method be applied to PIC 16f689

    ReplyDelete

Post a Comment

Popular posts from this blog

PIC 16F877A Microcontroller Based Electronic Lock 16x2LCD 4x3 Keypad

 Circuit Diagram Security is a prime concern in our day-today life. Everyone wants to be as much secure as possible. An access control for doors forms a vital link in a security chain. The microcontroller based digital lock for Doors is an access control system that allows only authorized persons to access a restricted area. An electronic lock or digital lock is a device which has an electronic control assembly attached to it. They are provided with an access control system. This system allows the user to unlock the device with a password. The password is entered by making use of a keypad. The user can also set his password to ensure better protection. The major components include a Keypad, LCD and the controller PIC16F877A. This article describes the making of an electronic code lock using the 16F877A microcontroller. The system is fully controlled by the 8 bit microcontroller 16F877A which has a 8Kbytes of ROM for the program memory. The password is stored in the

Electronic Voting Machine Using 8051 Microcontroller (AT89C51)

  Circuit Electronic voting machine has now replaced the traditional mechanism of voting due to several advantages like security, automatic counting etc. This project presents a way to develop an electronic voting machine which displays the count of votes on a 16x2 LCD interface. A user can get his/her vote register through a set of switches (one for each candidate). After every cast of vote, the subsequent count can be seen on LCD. The circuit uses AT89C51 microcontroller and the code for the project has been written in C. This LCD based electronic voting machine is designed for four candidates. The input part consists of a set of six tactile switches. The switches and 16x2 LCD are interfaced to microcontroller AT89C51 for various operations and displays. The provision of casting votes for the candidates has been provided through four of these switches. These switches are made active high and connected to pins 2-5 (P1^1 – P1^4) of the controller. The remaining two

89C51 Based Digital Thermometer Using DS1820

Introduction The hardware configuration when using multiple 1-Wire temperature sensors like the DS1820 is very simple, as illustrated in the block diagram below. A single-wire bus is used for communication between the microcontroller and the temperature sensor. It is also possible to power the devices direclty via this 1-Wire bus. An almost unlimited number of 1-WireTM devices can be connected to the bus because each device has a unique 64-bit ROM code identifier which is used to address each sensor   Temperature measurement using DS1820 sensor. Use of ‘1-wire’ protocol... Temperature measurement is one of the most common tasks performed by the microcontroller. A DS1820 sensor is used for measurement here. It is capable of measuring temperature in the range of -55 °C to 125 °C with 0.5 °C accuracy. For the purpose of transferring data to the microcontroller, a special type of serial communication called 1-wire is used. Due to a simple and wide use of these sensors, commands us